Wanpipe Asterisk Configuration File
- Wanpipe AFT A101/2/4/8 config for Asterisk/Zaptel
- Wanpipe AFT A200/400 config for Asterisk/Zaptel
- Wanpipe AFT A500 config for TDM API/SMG/Asterisk
Wanpipe Configuration file for Asterisk/Zaptel SoftPBX:
Skeleton:
[devices]
<Wanpipe device definition>
[interfaces]
<List of all wanpipe interfaces: w1g1/w2g1 (for Linux) or wag1/wbg1 (for FreeBSD) >
[wanpipe#]
<List of wanpipe device configuration parameters (see below)>
[w#g1]
<List of wanpipe interface configuration parameters (see below)>
Wanpipe Asterisk Configuration for A101/A102/A104/A108 T1/E1 cards:
[devices]
wanpipe1 = WAN_AFT, Comment # For old AFT-A101/AFT-A102:
wanpipe1 = WAN_AFT_TE1, Comment # For AFT-A101/AFT-A102/AFT-A104/AFT-A108:
[interfaces]
w#g1 = wanpipe1, , TDM_VOICE, Comment
[wanpipe1]
| Parameter |
Value |
|
Description
|
| CARD_TYPE |
AFT |
|
Define AFT card type
|
AUTO_PCISLOT
|
YES
NO
|
|
Enable/Disable AUTO PCI detection. This parameter can be set to YES only if you have only one card of the same type. If this option is enabled, PCISLOT/PCIBUS options are ignored (NOTE: A101/A102/A104/A108 T1/E1 is treated as the same card).
|
PCISLOT
|
|
|
|
PCIBUS
|
|
|
|
FE_MEDIA
|
T1
E1
|
|
Front End Media type.
|
FE_LCODE
|
B8ZS
AMI
HDB3
|
T1
T1/E1
E1
|
Front End Line Coding.
|
FE_FRAME
|
ESF
D4
UNFRAMED
SLC-96
NCRC4
CRC4
|
T1
T1
T1/E1
T1
E1
E1
|
Front End Framing. |
FE_LINE
|
Number
|
T1/E1
|
Front End Port/Line number.
(For A108, FE_LINE=1..8; for A104, FE_LINE=1..4)
|
| TE_CLOCK |
MASTER
NORMAL
|
|
T1/E1 clock source.
Normal - slave clock, clock is received from telco (default). Master- master clock, use HW oscillator clock.
|
| TE_REF_CLOCK |
Number
|
|
T1/E1 Reference clock source.
This options allows one to use the incoming clock from a different port as a clock source to this port. This option works only if TE_CLOCK is MASTER. If TE_REF_CLOCK is set to 0, the feature is disable. |
TE_HIGHIMPEDANCE
|
YES
NO
|
|
Enable/Disable RX High Impedance mode. |
TE_RX_SLEVEL
|
120
180
300
360
430
300
225
175
120
|
T1/E1:12dB
T1/E1:18dB
T1/E1:30dB
T1:36dB
E1:43dB
T1/E1:HI:30dB
T1/E1:HI:22.5dB
T1/E1:HI:17.5dB
T1/E1:HI:12dB |
Define T1/E1 Receive sensitivity (Max Cable loss allowed) (dB).
('HI' means that these options available if TE_HIGHIMPEDANCE parameter is set to YES). |
LBO
|
0DB
7.5DB
15DB
22.5DB
0-110ft
110-220ft
220-330ft
330-440ft
440-550ft
550-660ft
120OH
75OH
|
T1
T1
T1
T1
T1
T1
T1
T1
T1
T1
E1
E1
|
Define Line Buil-Out (transmit waveshape) |
FE_TXTRISTATE
|
YES
NO
|
|
Enable/Disable T1/E1 Tx Tri-State mode.
|
MTU
|
|
|
|
TDMV_SPAN
|
Number
|
|
Define span number for this device
|
TDMV_DCHAN
|
Number
|
|
Set to 0 if HW DCHAN is disabled. To enable HW DCHAN support, set it to dchan number
|
TDMV_HW_DTMF
|
YES
NO
|
|
Enable/Disable Hardware DTMF detection (Echo Cancellation module is required) |
TDMV_HW_FAX_DETECT
|
YES
NO
|
|
Enable/Disable Hardware Fax detection (Echo Cancellation module is required) |
| TE_IGNORE_YEL |
YES
NO
|
|
Ignore incoming Yellow alarms and do not stop transmitting. Needed for ATM systems where Yellows don't clear till cells are aligned
|
| HWEC_CLKSRC |
YES |
|
Changes the port that will be used to recover a clock for the HWEC. By default the first port started is used.
Placed in the wanpipeX.conf file that you wish to be the clock source.
|
[w#g1]
| Parameter |
Value
|
|
Description
|
| ACTIVE_CH |
ALL
|
|
Bit-map of active T1/E1 channels/timeslots
|
TDMV_ECHO_OFF
|
YES
NO
|
|
Disables or enables SWEC
|
TDMV_HWEC
|
YES
NO
|
|
Enable/Disable Echo Cancellation for this wanpipe interface
|
Wanpipe Asterisk Configuration for A200/A400 Analog cards:
[devices]
wanpipe1 = WAN_AFT_ANALOG, Comment
[interfaces]
w#g1 = wanpipe1, , TDM_VOICE, Comment
[wanpipe1]
| Parameter |
Value |
|
Description
|
| CARD_TYPE |
AFT |
|
Define AFT card type
|
AUTO_PCISLOT
|
YES
NO
|
|
Enable/Disable AUTO PCI detection. This parameter can be set to YES only if you have only one card of the same type. If this option is enabled, PCISLOT/PCIBUS options are ignored (NOTE: A101/A102/A104/A108 T1/E1 is treated as the same card).
|
PCISLOT
|
Number |
|
PCI Slot number |
PCIBUS
|
Number |
|
PCI Bus number
|
FE_MEDIA
|
FXO/FXS |
|
Front End Media type.
|
| TDMV_LAW |
MULAW
ALAW
|
|
|
TDMV_OPERMODE
|
See note (1)
|
|
FXO operation mode.
|
| RM_BATTTHRESH |
3
|
|
Battery threshhold.
|
RM_BATTDEBOUNCE
|
16 |
|
Battery debounce parameter.
|
| RM_NETWORK_SYNC |
|
|
|
| RM_FXSTXGAIN |
0
-35
35
|
0dB
-3.5dB
3.5dB
|
Analog FXS TX path gain
|
| RM_FXSRXGAIN |
0
-35
35
|
0dB
-3.5dB
3.5dB
|
Analog FXS RX path gain
|
| RM_FXOTXGAIN |
-165 to 135
|
-16.5db to 13.5db
|
Analog FXO TX path gain
|
RM_FXORXGAIN
|
-165 to 135
|
-16.5db to 13.5db |
Analog FXO RX path gain
|
RM_PULSEDIALING
|
|
|
|
| RM_RELAXCFG |
|
|
|
MTU
|
|
|
|
TDMV_SPAN
|
Number
|
|
Define span number for this device
|
TDMV_HW_DTMF
|
YES
NO
|
|
Enable/Disable Hardware DTMF detection (Echo Cancellation module is required) |
| |
|
|
|
[w#g1]
| Parameter |
Value
|
|
Description
|
| ACTIVE_CH |
ALL
|
|
Bit-map of active T1/E1 channels/timeslots
|
TDMV_ECHO_OFF
|
YES
NO |
|
Disable/Enable SWEC
|
TDMV_HWEC
|
YES
NO
|
|
Enable/Disable Echo Cancellation for this wanpipe interface
|
Wanpipe TDM API Configuration for A500 BRI cards:
[devices]
wanpipe1 = WAN_AFT_ISDN, Comment
[interfaces]
w#g1 = wanpipe1, , TDM_VOICE_API, Comment
[wanpipe1]
| Parameter |
Value |
|
Description
|
| CARD_TYPE |
AFT |
|
Define AFT card type
|
AUTO_PCISLOT
|
YES
NO
|
|
Enable/Disable AUTO PCI detection. This parameter can be set to YES only if you have only one card of the same type. If this option is enabled, PCISLOT/PCIBUS options are ignored (NOTE: A101/A102/A104/A108 T1/E1 is treated as the same card).
|
PCISLOT
|
Number |
|
PCI Slot number |
PCIBUS
|
Number |
|
PCI Bus number
|
FE_MEDIA
|
BRI |
|
Front End Media type.
|
| FE_LINE |
Number |
1-12
|
Port number
|
| TDMV_LAW |
MULAW
ALAW
|
|
|
| RM_BRI_CLOCK |
LINE
OSC
|
|
Clocking mode
LINE: card might use this port as clocking source if current port is in connected state
OSC: card will never use this port as a clocking source.
|
MTU
|
|
|
|
TDMV_SPAN
|
Number
|
|
Define span number for this device
|
TDMV_HW_DTMF
|
YES
NO
|
|
Enable/Disable Hardware DTMF detection (Echo Cancellation module is required) |
| |
|
|
|
[w#g1]
| Parameter |
Value
|
|
Description
|
| ACTIVE_CH |
ALL
|
|
Bit-map of active BRI channels/timeslots
|
TDMV_ECHO_OFF
|
|
|
|
TDMV_HWEC
|
YES
NO
|
|
Enable/Disable Echo Cancellation for this wanpipe interface
|
| 
