#================================================
# WANPIPE1 Configuration File
#================================================
#
# Date: Thu Jan 19 20:45:37 EST 2006
#
# Note: This file was generated automatically
#       by /usr/sbin/wancfg program.
#
#       If you want to edit this file, it is
#       recommended that you use wancfg program
#       to do so.
#================================================
# Sangoma Technologies Inc.
#================================================

[devices]
wanpipe1 = WAN_AFT_ANALOG, Comment

[interfaces]
w1g1 = wanpipe1, , TDM_VOICE_API, Comment

[wanpipe1]
#-------- DEVICE / DRIVER BINDING ----------------------------------

CARD_TYPE 	= AFT	#AFT: Same for all aft cards must
                        #This value must be hardcoed to AFT for all
                        #aft cards.
	
S514CPU 	= A     #Used by A101/2 driver to determine T1/E1 port
                        #A - port 1   
                        #B - port 2
		
			#For A104 driver: Always set this value to A!

#-------- PCI SETUP ----------------------------------------------


AUTO_PCISLOT 	= YES    #Auto detect PCI/BUS info for this card type
                        #NO - disable this option
                        #YES- enable this option
                        #     if enabled bottom two options 
			#     PCISLOT and PCIBUS will not be used. 
                        #     Therefore one can set the to arbitrary value 
                        #     or remove them all together.

PCISLOT 	= 2     #PCI SLOT Number: 
                        #Valid values = any number
    
PCIBUS  	= 2     #PCI BUS Number:
			#Valid values = any number


#--------------FRONT END SETUP -----------------------------------

FE_MEDIA	= FXO/FXS	#FXO/FXS ports

TDMV_LAW	= MULAW		#Options: MULAW or ALAW

TDMV_OPERMODE	= FCC  		#Options: FCC,TBR21 ...


#------------- GENERAL SETUP -------------------------------------

MTU 		= 1500    #Global MTU Value
                          #Note: This value is overwritten by the 
                          #      interface MTU value below if it exists.
                          #Values: any number [ suggested 128 - 4086 ]

UDPPORT 	= 9000    #OBSELETE option 
                          #Old wanpipemon used sockets to connect to
                          #device driver.

TTL		= 255     #OBSELETE option
			  #Old wanpipemon used sockets to connect to
                          #device driver.

IGNORE_FRONT_END = NO	  #Ignore Fronte End State
                          #NO - Do not ignore front end state,
                          #     therefore if state changes, change the
                          #     state of the above protocol.
                          #YES- Igonore front end state
                          #     Thus if front end goes down, the protocol
                          #     will not know. 

#------------------ TDM SETUP ------------------------------
TDMV_SPAN =  1    	  #TDM API Span Number
                          #From 1 to Unlimited


[w1g1]   		  #Leave Default

ACTIVE_CH	= ALL     #All channels are to be enabled on this span

MTU		= 16	  #RX/TX Chunk/Sample Size per channel in bytes.
			  #Options:
			  #  8 -> 1ms
			  # 16 -> 2ms   (Default)
			  # 40 -> 5ms   (A104SH & A108)
			  # 80 -> 10ms  (A104SH & A108)

TDMV_HWEC	= NO 	  #Hardware Echo Cancellation Control
			  #Must confirm with "wanrouter hwprobe"
		          #That echo cancellation is supported
			  #Optons: YES - Enable
			  #         NO - Disable