#================================================
# WANPIPE1 Configuration File
#================================================
#
# Date: Thu Jan 19 20:45:37 EST 2006
#
# Note: This file was generated automatically
#       by /usr/sbin/wancfg program.
#
#       If you want to edit this file, it is
#       recommended that you use wancfg program
#       to do so.
#================================================
# Sangoma Technologies Inc.
#================================================

[devices]
wanpipe1 = WAN_AFT_TE1, Comment   #WAN_AFT_TE1 - Indicates A104/8/4d/8d cards
				  #WAN_AFT     - Indicates A101/2 card	

[interfaces]
w1g1 = wanpipe1, , TDM_VOICE_API, Comment

[wanpipe1]
#-------- DEVICE / DRIVER BINDING ----------------------------------

CARD_TYPE 	= AFT	#AFT: Same for all aft cards must
                        #This value must be hardcoed to AFT for all
                        #aft cards.
	
S514CPU 	= A     #Used by A101/2 driver to determine T1/E1 port
                        #A - port 1   
                        #B - port 2
		
			#For A104 driver: Always set this value to A!

#-------- PCI SETUP ----------------------------------------------


AUTO_PCISLOT 	= YES    #Auto detect PCI/BUS info for this card type
                        #NO - disable this option
                        #YES- enable this option
                        #     if enabled bottom two options 
			#     PCISLOT and PCIBUS will not be used. 
                        #     Therefore one can set the to arbitrary value 
                        #     or remove them all together.

PCISLOT 	= 2     #PCI SLOT Number: 
                        #Valid values = any number
    
PCIBUS  	= 2     #PCI BUS Number:
			#Valid values = any number


#--------------FRONT END SETUP -----------------------------------

FE_MEDIA	= T1    #Front End Type: 
			#T1 - set front end for T1 mode
                        #E1 - set front end for E1 mode

FE_LCODE	= B8ZS  #Front End Line Coding
			#If T1:  B8ZS or AMI
                        #   E1:  HDB3 or AMI        

FE_FRAME	= ESF   #Front End Framing
			#If T1:  ESF or D4 
                        #   E1:  CRC4 or NCRC4

FE_LINE		= 1       #Front End Line number.
			  #Used by A104 driver to determine T1/E1 port
			  #Valid values are: 1-4
			  #
                          #The A101/2 driver doesn't use this option   
                          #so one should hardcode it to 1 or 
                          #remove it all together.
					
	
TE_CLOCK 	= NORMAL  #T1/E1 Clock Source
                          #NORMAL - slave clock, clock is received from telco
                          #         This is always the DEFAULT
                          #MASTER - master clcok, use hw oscillator clock
                          #         Only used in back to back mode or
                          #         when specified by telco.
 
TE_REF_CLOCK 	= 0	  #T1/E1 Reference Clock Source
                          #This option allows one to use the incoming clock
                          #from a different port as a clock source to this
                          #port.  FOR THIS OPTION TO WORK: TE_CLOCK=MASTER
			  #Valid options: 0   - disable 
                          #               1-4 - use clock from particular port

ACTIVE_CH	= ALL	  #Specify T1/E1 Active channels (timeslots)
                          #Since AFT cards support channelization this
                          #option MUST BE HARDCODED TO:  ALL!

TE_HIGHIMPEDANCE	= NO  #Set the Front Ent chip in High Impedance mode
                              #used for datascoping:
                              #NO - Disable high impedance mode (DEFAULT)
                              #YES - Enable hight impedance mode 
                              #      (only if you know what you are doing)

LBO 		= 0DB     #Front End Line Buildout
                          # 0db     (Default)  
                          # 7.5dB     
                          # 15dB      
                          # 22.5dB     
                          # 0-110ft    
                          # 110-220ft  
                          # 220-330ft  
                          # 330-440ft  
                          # 440-550ft  
                          # 550-660ft 
  
FE_TXTRISTATE	= NO	  #Front End Tri-State Mode
                          #Disable front end chip TX mode
                          #Used for datascoping or connecting multiple ports
                          #together where one port is operating normally and others
                          #are tristated, thus only receiving.
                          #NO - Disable tristae mode
                          #YES- Enable tristate mode

MTU 		= 1500    #Global MTU Value
                          #Note: This value is overwritten by the 
                          #      interface MTU value below if it exists.
                          #Values: any number [ suggested 128 - 4086 ]

UDPPORT 	= 9000    #OBSELETE option 
                          #Old wanpipemon used sockets to connect to
                          #device driver.

TTL		= 255     #OBSELETE option
			  #Old wanpipemon used sockets to connect to
                          #device driver.

IGNORE_FRONT_END = NO	  #Ignore Fronte End State
                          #NO - Do not ignore front end state,
                          #     therefore if state changes, change the
                          #     state of the above protocol.
                          #YES- Igonore front end state
                          #     Thus if front end goes down, the protocol
                          #     will not know. 

TDMV_SPAN =  1    	  #TDM API Span Number
                          #From 1 to Unlimited

TDMV_DCHAN = 24		  #TDM DCHAN PRI HW HDLC Channel
			  #0  - no pri channel used
			  #24 - T1 pri channel
			  #16 - E1 pri channel 
			  #The TDM PRI Span/Chan device will rx/tx HDLC
			  #based frames.
			  	  

[w1g1]   		  #Leave Default

ACTIVE_CH	= ALL     #All channels are to be enabled on this span

MTU		= 16	  #RX/TX Chunk/Sample Size per channel in bytes.
			  #Options:
			  #  8 -> 1ms
			  # 16 -> 2ms   (Default)
			  # 40 -> 5ms   (A104SH & A108)
			  # 80 -> 10ms  (A104SH & A108)
			
TDMV_HWEC	= NO 	  #Hardware Echo Cancellation Control
			  #Must confirm with "wanrouter hwprobe"
		          #That echo cancellation is supported
			  #Optons: YES - Enable
			  #         NO - Disable